What pin is OBD2 power?
Pin 16
Pin 16 supplies power and is connected to the battery of the car.
What OBD2 protocol does Hyundai use?
OBD-II Signal Protocols ISO 9141-2. This protocol has a data rate of 10.4 kbaud, and is similar to RS-232.
What pin is ground at an OBD-II connector?
SAE J1962 (OBD-II) Type “B” Connector (24V)
| Pin Number | Description |
|---|---|
| 2 | SAE J1850 VPW Bus + (10.4Kbps) |
| 3 | CCD Bus + |
| 4 | Chassis Ground |
| 5 | Signal Ground |
Where is the diagnostic plug on a Hyundai Santa Fe?
OBD connector location for Hyundai Santa Fe 3 Phase 1 (2012 – 2015)
- The OBD2 plug is located on the left of the steering wheel.
- We can see the OBD port.
- The OBD2 diagnostics port.
Is the OBD2 port always powered?
So yes, the OBD port’s power pin (battery positive 16): MUST be unswitched (always connected to battery power)
Does OBD2 work on Hyundai?
The Launch Creader VII is a great OBD2 scanner for Hyundai and Kia vehicles. It can scan the brake system (ABS), Airbag (SRS), Engine, and Transmission on most cars, SUVs, and VANs. Any Hyundai owner who needs to know why the transmission is not shifting or why the ABS or SRS lights are on is a great scanner.
What is DLC pin?
The DLC or Data Link Connector is an OBD II, 16 pin, standard connector used in all automobiles manufactured since 1996. In today’s vehicles, it’s in constant communication with the CAN, or Computer Area Network.
Where is the OBD port on a 2005 Hyundai Santa Fe?
The OBD-II port in a Honda Santa Fe is located to the left and below the steering wheel. If You are sitting in the driver’s seat, there is an access panel in front of Your right knee. Place Your fingers in the slot and pull out on the panel to remove it.
What OBD port does my car have?
The OBD2 port location can vary depending on your car model. However, it is usually found within reach of the driver, underneath the steering wheel. Scroll down to see where the OBD2 port is located in your car! Additionally, you can also check the location of the OBD2 port in your car’s manual.
How many pins does an OBD2 connector have?
16 pin locations
The OBD II connector has 16 pin locations which are numbered as shown below. If pins 5, 6, 14 and 16 are populated, the vehicle supports CAN. If pins 5, 7, 16 and, optionally, 15 are populated, the vehicle supports ISO or KWP. If pins 2, 5 and 16 are populated, the vehicle supports VPW.
What is the VSS pinout for the Hyundai OBD II cable?
* ’08 iLoad manual has VSS at pin 3. Some OBD-II cables schemes: According to 5 reports in our database ( 3 positive and 0 negative) the Hyundai OBD II diagnostic interface pinout should be correct. If you did publish instruction for Do-It-Yourself device with this pinout, share the link with us.
Is the Hyundai OBD-II diagnostic interface pinout correct?
Some OBD-II cables schemes: According to 5 reports in our database ( 3 positive and 0 negative) the Hyundai OBD II diagnostic interface pinout should be correct. If you did publish instruction for Do-It-Yourself device with this pinout, share the link with us.
Where is the OBD2 connector on a Honda Accord?
Some connectors have been located behind ashtrays, under the passenger seat and even over by the passengers door. OBD-2 connector must have pins 4, 5 for ground connections and pin 16 for 12 volt power supply from the vehicle battery. What is OBD DTC?