Is the Chevy 327 a good engine?
The 327 worked very well with the carburetors, pistons, cylinder heads, intake manifolds and camshaft used that were available in the late 60’s, and its big horsepower-per-cubic-inch potential made it a favorite among enthusiasts for both the street and strip.
How much horsepower can you get from a 327?
Rated at 375 hp, the fuel-injected 327 was a high-winding screamer, as satisfying to drive as any big-block. At the other end of the spectrum, the 327 was also offered at much more pedestrian power levels, as low as 210 hp (gross).
Is a 327 rare?
The L74, 300hp 327s Chevy IIs totaled 319. Few knew these two 327 RPOs even existed. Both are ultra rare today. Either of these 327 engines in the Chevy II, Chevelle and big car could be had with an automatic or manual transmission-three- or four-speed.
When did Chevy stop making the 327?
1969
The 327 was a mainstay of Chevrolet’s engine lineup from 1962 through 1969, when it made its final appearance as the standard V-8 in that year’s fullsize Chevys, and as a low-cost option over the base 307-inch V8 in the Chevelle, Nova and Camaro.
Why is a 327 better than a 350?
The bottom line here is simple; no matter what you do to a 327, if you do the same thing to a 350, it WILL make more horsepower and torque than a 327 will, period. The same thing goes with ANY engine when comparing cubic inches and power, especially when you are talking about making more torque with longer strokes.
How high can a 327 rev?
The bottom end of a stock 327 can be safely spun up to 6500 RPM if it is in good shape. A stock 327 with power pack heads and a stock cam will run out of breath above 5000 RPM. The power pack heads have small valves (1.72 intake &1. 50 exhaust), and a stock cam is designed to make power below 4500 RPM.
What was the first year for the 327 Chevy engine?
1962
The 327 debuted in 1962. It featured a 4.00-inch bore and a 3.25-inch stroke, increases of an eighth-inch and a quarter-inch, respectively, over the 283.
How do I identify a 327 engine?
Location. The 327 Chevy engine is stamped on a machined pad on the front passenger side cylinder head usually behind the alternator.
What is a Chevy 327 bored 30 over?
A 30 over 327 is 331.6; 60 over is 336.6.
How much does it cost to rebuild a 327 engine?
is a chevy 327 a good engine? How Much Does It Cost To Fully Rebuild An Engine? Engine rebuilding is typically about $2,500 in parts and labor in cost. A quick and easy method of engine repair would be to replace bearings and seals, and then take out, remove, and re-inflate the engine. Is A 327 A Good Engine?
How good is a 327 engine?
The 327 engine was Chevy’s best production engine in numbers and in longevity. This was mainly because of the 327 engine’s part interchangeability. You could swap out parts from different past year model vehicles and use them in the 327 engine. And we’re talking about parts from different vehicle models spanning back almost 45 years.
How much is a 327 engine worth?
327 ci — 350 HP, 365 HP, 375 HP. Now offered in turnkey packages. (This is the Chevy-24 page) These are nostalgic era engines. from a real barn find!! Base Pricing from: 327ci 300 HP priced from $3995 (+ $995 for turnkey package) 327ci 330 HP priced from $4195 (+ $995 for turnkey package) 327ci 350 HP priced from $4395 (+ $995 for turnkey
What is firing order for 327 Chevy?
In the case of reverse rotation marine engines where the distributor rotation is opposite of a standard rotation engine, the reverse rotation firing order becomes 1-2-7-5-6-3-4-8 . Be sure on the Chevy V8 that the #5 and #7 wires aren’t accidentally transposed.